SK, BT and HSK spindle tapers: understanding and choosing

Technical · · 5 min read

Makino a61nx-5E – view 1

The spindle taper is the interface between the machine and the toolholder. It governs how precisely the tool is located, the rigidity of the assembly, the permissible rotational speed and, very practically, which toolholders you can use. On a specification sheet it takes only a few characters, SK 40, BT 40 or HSK-A63, but those few characters decide whether your stock of toolholders will work on a new machine.

The 7/24 taper: the principle

On milling machines and machining centers, two families of interfaces have prevailed: the 7/24 taper and HSK. The first is a so-called "steep" taper: the diameter changes by 7 units over 24 units of length, giving a half-angle of about 8.3°. Unlike the much narrower Morse taper, this taper is not self-holding: the toolholder releases without effort, which matters a great deal for automatic tool changing. Its short length brings the cutting edge closer to the spindle bearings and gives good bending stiffness.

Because the taper alone does not transmit high torque, drive keys on the spindle engage slots in the toolholder flange. The toolholder is pulled into the spindle by a drawbar that grips a pull stud screwed into the back of the taper. Most often, this clamping is provided by disc springs; release takes place at standstill, through a hydraulic or pneumatic cylinder.

SK, BT, CAT: same taper, different toolholders

Several toolholder families share the 7/24 taper:

  • SK, or ISO taper, standardised in ISO 7388-1 and formerly known in Germany as DIN 69871;
  • BT, of Japanese origin (MAS 403, JIS B 6339), taken up in ISO 7388-2, the most widespread in East Asia;
  • CAT, or "V-Flange", of American origin (ANSI B5.50).

The taper itself has the same basic dimensions, but the flanges, the V-grooves gripped by the tool changer, the drive slots and the pull studs differ. A BT toolholder can sometimes be loaded by hand into a CAT spindle with a suitable pull stud, but it does not work with the tool changer designed for the other system. The older DIN 2080 shanks, intended for clamping with a threaded drawbar, follow yet another logic.

Sizes 30, 40 and 50

The number gives the taper size. Standard sizes range from 10 to 60, but sizes 30, 40 and 50 are the ones most often found. The number is only a rough guide to the diameter: the largest diameter of the taper is 31.75 mm for a size 30, 44.45 mm for a size 40 and 69.85 mm for a size 50. A size 40 and a size 50 are obviously not interchangeable, even within the same standard.

The pull stud, a part not to overlook

The pull stud, screwed into the toolholder, is the part that the spindle clamping system grips. ISO 7388-3 standardises six forms, AD, AF, UD, UF, JD and JF, but there are also pull studs specific to certain manufacturers. Some are drilled and fitted with O-rings for coolant through the tool.

A pull stud from one system therefore does not necessarily suit another, even if the taper is identical. Before ordering toolholders, identify precisely the pull stud used by the machine, from the documentation or an existing pull stud.

HSK: hollow taper and face contact

HSK (Hohlschaftkegel, "hollow shank taper") was developed in the early 1990s and standardised in DIN 69893 and ISO 12164. Its 1:10 taper is short and hollow. It is clamped from the inside and seats on both the taper and the face of the flange: this dual contact gives precise axial location.

According to the sources consulted, this system has several advantages:

  • it is about 30% smaller and 50% lighter than a 7/24 taper, which makes tool changing easier and faster;
  • the face contact increases rigidity;
  • repeatability on tool change reaches 3 µm;
  • it suits high speeds: the thin wall of the hollow taper expands with the spindle, and the face contact stops the toolholder from being drawn in.

By contrast, a solid 7/24 taper is stiffer than the spindle that holds it. At high speed, centrifugal force expands the spindle mouth more than the taper: the toolholder moves deeper along the Z axis, which can produce out-of-tolerance parts.

HSK forms

HSK comes in forms designated by letters, and in sizes that correspond to the flange diameter in millimetres. HSK-A63 is thus a form A HSK with a 63 mm flange.

  • A: the basic form, for automatic tool changing.
  • B: a variant for high torque, with a larger flange relative to the taper.
  • C and D: simplified versions of A and B for manual changing, without the groove for the tool changer or the recess for an identification chip.
  • E and F: close to A and B, designed for very high-speed machining, from about 20,000 rpm upwards.
  • T: a form compatible with form A, with more precise drive slots, intended for turning tools.

What it changes when buying a used machine

The spindle taper weighs heavily in the choice of a used machine, because it commits all the tooling:

  • Your existing stock. If your toolholders are SK 40, a BT 40 or HSK-A63 machine will in principle require other toolholders. Check the exact standard, not just the number.
  • The pull stud. Identify its form and order pull studs that match the machine's documentation.
  • The toolholders supplied. Count them and examine their condition: a damaged, dirty or marked taper no longer locates correctly. All tapers are sensitive to chips, knocks and dirt, hence the air blast during tool change on many CNC machines.
  • The intended use. For very high-speed machining, an HSK form E or F makes sense; for everyday machining, a 7/24 taper remains very widespread.

On the pages of our stock, the spindle taper is shown when it was recorded on the machine or appears in the manufacturer's data. To check whether a machine is compatible with your tooling, contact us: every request gets an answer within 48 working hours.

Two examples in stock: the Makino a61nx-5E, with an HSK-A63 taper, and the Deckel Maho DMC 635V, with an SK 40 taper.

Further reading

A question about a machine?

Write or call us: answer within 48 working hours.

Contact us